sansui au amplifier loss a chanel | Sansui AU sansui au amplifier loss a chanel Hey folks, I held off for a few weeks to try and nut this one out myself but have hit . Are you looking for a great value holiday in Malta? Air Malta Holidays offers you the best deals on flights, hotels and car rentals. Whether you want to explore the historic cities, relax on the beaches or enjoy the nightlife, Air Malta Holidays has something for everyone. Book now and save on your next trip to the Mediterranean.
0 · Sansui AU
1 · SANSUI AU
$39.95
Sansui AU
Major issue is with the Tone control enabled, the left channel volume is very low . Try feeding a known good pre-amp output into the 'power amp in' sockets on the amp - see if the output is clean. The connectors and switches on these amplifiers seem particularly prone to oxidisation and therefore poor contacts - which can be intermittent - check all the connectors are tight and clean. Hey folks, I held off for a few weeks to try and nut this one out myself but have hit . It seems that the problem is in the amplifier, the noise remains in the left channel .
Major issue is with the Tone control enabled, the left channel volume is very low and barely audible at about 50%. Increasing the volume some more, introduces distortion. With Tone/Filter in defeat. mode, both channels work properly. I have an AU-D11ii that functions great except for the phono in which I have a weak left channel. I know these are very rare amps and there aren’t many out of them out there, but if anybody has encountered a weak phono channel and resolved it, it would be good to know what the solution was.
patek philippe nautilus 18k rose gold
The restoration went well, the amplifier sounds very good but there is a problem in the left channel, sometimes with quiet music the sound is bad, like distorted, and the volume potentiometer scratches, always on that channel. It was . Hey folks, I held off for a few weeks to try and nut this one out myself but have hit a wall. I've recapped the entire amp and replaced all small transistors. RH sounds absolutely amazing but LH is very distorted. 1. Checked that it was not a speaker issue by swapping LH/RH 2. I have just put my AU 317 back into service and it appears the left channel is flakey. I just bought some new Wharfedale Denton 85s and ran them all day yesterday, at low to moderate levels, without any problems. Just before lights out last night I noticed the left channel was louder than. I was interested in listening to an old Sansui amplifier – so purchased an AU-222 from a popular auction site. I set it up in my study – and the sound was, until the weekend, smooth, warm and elegant. Loved it. Then the trouble .
It seems that the problem is in the amplifier, the noise remains in the left channel even reverse the RCA input connectors, also remains to replace speaker. I will continue with cleaning switches and connectors . I was able to adjust the right channel to 13mV but I have alway 0mV on the left one. I measured several times, ampli was running for 30min or more, speakers connected, volume at minimum and I can measure 12.9/13/13.1 mV always on .
Everything was great, but sometimes the right channel stopped working. I noticed that the problem may be in the switches, so I bought Deoxit D100 and Fadergrease and cleaned all switches and potentiometers. I turned on the amplifier and heard a noise. I am ashamed to admit that I have royally screwed up and lost the right channel on my AU-D607. :pity: It is a Japanese market unit that uses 100 volt power. Major issue is with the Tone control enabled, the left channel volume is very low and barely audible at about 50%. Increasing the volume some more, introduces distortion. With Tone/Filter in defeat. mode, both channels work properly. I have an AU-D11ii that functions great except for the phono in which I have a weak left channel. I know these are very rare amps and there aren’t many out of them out there, but if anybody has encountered a weak phono channel and resolved it, it would be good to know what the solution was.
The restoration went well, the amplifier sounds very good but there is a problem in the left channel, sometimes with quiet music the sound is bad, like distorted, and the volume potentiometer scratches, always on that channel. It was .
Hey folks, I held off for a few weeks to try and nut this one out myself but have hit a wall. I've recapped the entire amp and replaced all small transistors. RH sounds absolutely amazing but LH is very distorted. 1. Checked that it was not a speaker issue by swapping LH/RH 2.
I have just put my AU 317 back into service and it appears the left channel is flakey. I just bought some new Wharfedale Denton 85s and ran them all day yesterday, at low to moderate levels, without any problems. Just before lights out last night I noticed the left channel was louder than. I was interested in listening to an old Sansui amplifier – so purchased an AU-222 from a popular auction site. I set it up in my study – and the sound was, until the weekend, smooth, warm and elegant. Loved it. Then the trouble . It seems that the problem is in the amplifier, the noise remains in the left channel even reverse the RCA input connectors, also remains to replace speaker. I will continue with cleaning switches and connectors .
SANSUI AU
I was able to adjust the right channel to 13mV but I have alway 0mV on the left one. I measured several times, ampli was running for 30min or more, speakers connected, volume at minimum and I can measure 12.9/13/13.1 mV always on . Everything was great, but sometimes the right channel stopped working. I noticed that the problem may be in the switches, so I bought Deoxit D100 and Fadergrease and cleaned all switches and potentiometers. I turned on the amplifier and heard a noise.
Sales and reservations. Tel: 1800 132 476. Calling from overseas. TTY users phone 133 677 then ask for 1800 132 476.
sansui au amplifier loss a chanel|Sansui AU
